Hot Racing

Alum Bearing Saver Steering Kit - T-Maxx E-Maxx

Hot Racing aluminum steering bellcrank with built-in servo saver for the Traxxas T-Maxx or E-Maxx. Requirements: E-Maxx or T-Maxx that uses the Traxxas 4945 steering rack (refer to your vehicle's manual)Features:Super-tough, fully adjustable servo...

Aluminum Front Bumper Mount, for Axial SCX24

Hot Racing aluminum front bumper mount frame crossmember for the Axial SCX24 vehicles.Features:Stronger and more rigid than factory plastic cross-member for a more rigid frame and more predictable and consistent chassis performanceOne-piece CNC machined...

Knuckle Portal Cover, Brass,

Features:CNC machined solid brassHeavy to add weight to vehicle for greater stability.Improve weight distribution for better performanceDirect replacement for factory plastic steering knuckles Portal Gear CoverSpecifications:Weight 41g (1.4oz) eachCNC...

Steel Pinion & Spur Gear Kit, 18/58T 32P (0.8Mod)

Hot Racing Blue Power Up HD 58T 32pitch Spur Gear for the Traxxas Rustler, Stampede and Slash. FEATURES: Rugged 0.8 Module/32pitch teeth for total reliability on brushless power. CNC Machined Harden Black steel teeth attached to hub with three screws One...

Alum +6mm 17mm Hubs, Hex Serrated Nuts, for Traxxas MT

Hot Racing's +6mm/side extended 17mm hex hub wheel adapters for the Traxxas E-Maxx, E-Revo, Revo, Summit, and T-Maxx. These increase the track width of the vehicle to increase stability and replace the existing hexes so the vehicle can accept wheels with...

Composite Gear Case with Aluminum Motor Plate

Composite transmission gearbox case with aluminum motor plate and arm mounts for use in the Traxxas Bandit, Rustler, 2WD Stampede, and 2WD Slash.YOU WILL RECEIVE:- One (1) composite transmission case with aluminum heat sink motor plate- Left and right...

Wheel Hub Adapters, Aluminum,

Hot Racing's aluminum 12mm to 17mm hex wheel hub adapters. These adapters are compatible with many 1/10th scale vehicles with factory 12mm hex hubs and allow the use of 17mm hex wheels, all while adding a 10mm width extension per side of the vehicle for...

Aluminum Front Bumper Fairlead Light Buckets, for Axial SCX24

Hot Racing CNC machined aluminum front bumper with 3mm LED light buckets, winch fairlead for use with Axial SCX 24.Features:Billet CNC machined aluminumAnodized a stylish flat blackIntegrated brush guardsLight buckets for 3mm LED...

Blue Internal Spring Air Shocks, 100mm

Hot Racing Blue Internal Spring Air Shock Set for the Rock Crawlers that use 100mm shocks FEATURES: CNC Aluminum shock bodies 7mm stainless steel shaft Air Damping Internal springs YOU WILL RECEIVE: Two assembled alum shocks Two Hard spring Silver (.7mm)...

9.5g Brass KMC Machete Wheel Weights, for Axial SCX24

Hot Racing front or rear wheel weights for the stock 1.0in KMC Machete wheels on the Axial SCX24.Features:CNC machined solid brass billet9g each fitted to the wheels to lower the vehicles center of gravity, increase its stability, improve climbing,...

Secure Lock Front Bulkhead 1/16 Traxxas

Features:CNC machined 6061 aluminumAdded fastener points to secure, lock, and hold the gear mesh in placeReplaces the stock plastic bulkheadCNC machined 6061 aluminumAdded fastener points to secure, lock, and hold the gear mesh in placeReplaces the stock...

Rear Axle Housing Bearing Lock Out, for Traxxas UDR

Hot Racing's heavy duty aluminum rear axle housing lock out for the Traxxas Unlimited Desert Racer Series.YOU WILL RECEIVE:(1) left aluminum Rear Axle Housing Bearing Lock Out UDR(1) right aluminum Rear Axle Housing Bearing Lock Out UDRFeatures:CNC...

Steel Spur Gear (54t 32p) (Green) - Traxxas

Hot Racing light weight hardened steel 54 tooth, 32 pitch (0.8 Mod) spur gear for the 1/10 Traxxas Bandit, Rustler, 2WD Slash, 2WD Stampede, and Telluride vehicles. Comes with the following:- One (1) 54 tooth 32 pitch (0.8 Mod) spur gear- Three (3)...

Hex Hub Adapters, 12mm to 17mm w/ 6mm Offset

17mm Aluminum Hub Adapters with 12mm hex drive Change 1/10 scale 4wd truck to monster 17mm tire and Wheel. FEATURES: 6 mm Offset 17mm Hubs 12mm Hex Mount Aluminum construction Black and silver in color Very durable YOU WILL RECEIVE: (4) 17mm Wheel...

+4mm Steel Axles Brass Weight, for SCX24

+4mm Steel Axles Brass Weight, for SCX24Hot Racing front or rear wheel weights for Hot Racing +4mm Steel Drive Stub (SXTF39W04) on the Axial SCX24Features:- CNC machined solid brass billet- 5g each fitted to the +4mm Steel Drive Stub Axlex lower the...